Send Email
Send SMS
Search
Neotech Equipments Pvt. Ltd.
Neotech Equipments Pvt. Ltd.


Hydraulic Clamping Cylinders

Manufacturer of a wide range of products which include die lifter, swing cylinder, hydraulic work support cylinder, hydropneumatic intensifier, hydraulic block cylinder and pneumatic swing cylinder.

Die Lifter

REQUEST CALLBACK

Die Lifter
Approx. Rs 48,000 / Piece
Get Best Quote

In order to meet the diverse requirements of our valuable clients we are able to offer Die Lifter which is used in pairs or sets as per the slot length in the bolster & used for quick change of dies 8, we design the offered die lifter employing quality-proven components and leading technology in conformation with industry norms. Our offered die lifter is checked on various quality parameters in order to deliver defect-free range at clientele end.

Features:


  • Low maintenance
  • Corrosion resistance
  • Hardness

Descriptions:


  • Die Liters are used in pairs or sets as per the slot length in the bolster
  • Hydraulic piston fitted with needle roller bearing lift the die set allowing the die to be easily rolled in and out during die change process
  • Die Lifter is of rectangular cross section & can be fitted in Slot of bolster In 250 mm & 200 mm length die litters, four & three single acting,load return cylinders are fitted respectively
  • Various lengths can be assembled by using combinations of 250 & 200 length die lifters

Applications:


  • Die-lifters are used for quick change of dies 8
  • Tools on presses
  • Die can be pushed only in the direction of T slot

Installations:


  • Die-lifters are fixed in T slot
  • Die Lifters must be 1 mm below bolster top in unpressurized mode
  • Proper packing should be used to achieve this specific height
  • Connector Tubes are used to connect two units of die-litter in the row as shown in figure
  • Minimum two rows of die-litter are required to balance die weight
  • At one end hydraulic connection has to be given & other end has to be plugged

Operations:


  • For changing die, first unclamp the die-set
  • (Keep all cylinders in Parking stand, if die is clamped bydle clamping cylinders) Move ram up
  • Pressurize die-lifter, so that died is lifted by 2 mm above bolster top‘ Push die-set on trolley‘ Push new die set on bolster
  • Release die-lifter pressure so that die will rest on bolster

Specifications:


  • Operating pressure: 85 kg / cm3
  • Max. operating pressure 100 kg/ cm2
  • Force per unit length: 5 kglmm at 85 bar
  • Stroke: 3 mm
  • Lengths Available: 200, 250, 400, 450, 500, 600, and any length in step of 50 above 600 mm
Yes! I am Interested

Swing Cylinder

REQUEST CALLBACK

Swing Cylinder
Approx. Rs 5,000 / Piece
Get Best Quote

In our broad assortment of products, we are manufacturing, distributing, trading and supplying a qualitative gamut of Swing Cylinder. The offered swing cylinder is manufactured at our production unit using the better quality components and advance technology in accordance with defined industry standards. This swing cylinder has become the preferred choice of the patrons due to its striking features. We assure our customers that this swing cylinder is excellent on counts of durability and quality.

Features:


  • Robust construction
  • Smooth finish
  • Low maintenance

Specifications:

  • Bore diameter-30 mm
  • Maximum oil pressure- 200 bar
  • Minimum oil pressure-20 bar
  • Oil volume clamp- 9.2 cc
  • Oil volume declamp-19.8 cc
  • Force at 150 bar- 5.0 kN
  • Weight of the cylinder- 2.8 kg
Yes! I am Interested

View PDF

Hydraulic Work Support Cylinder

REQUEST CALLBACK

Hydraulic Work Support Cylinder
Approx. Rs 2,700 / Piece
Get Best Quote

We are engaged in manufacturing, distributing, trading and supplying a wide assortment of Hydraulic Work Support Cylinder. Our offered hydraulic cylinder is precisely manufactured at our well developed manufacturing unit employing high end technology. Additionally, we deliver this hydraulic cylinder from our end after conducting a proper test against them. Our honored clients can avail the offered hydraulic cylinder in various specifications.

Features:

  • Corrosion resistances
  • Sturdy construction
  • Durability

Specifications:


  • Minimum hydraulic operating pressure: 100 bar
  • Maximum hydraulic operating pressure: 200 bar
  • Maximum plunger contact force: 4 N
  • Support force: 1.5 kN at 150 bar

Advantages:


  • Manifold machining for this work support is very simple
  • Compact in size
  • Plunger is normally in retracted condition
Yes! I am Interested

Hydropneumatic Intensifier

REQUEST CALLBACK

Hydropneumatic Intensifier
Approx. Rs 18,000 / Piece
Get Best Quote

We are a prominent manufacturer, distributor, trader, and supplier of superior quality Hydro pneumatic Intensifier. The offered pneumatic intensifier is specifically manufactured using high grade components and advance technology. We assure our customers that our range of pneumatic intensifiers is quality tested against predefined quality parameters. Also, our customers can avail this pneumatic intensifier, as per their needs, at affordable price.

Features:


  • Durability
  • Perfect finish
  • Robustness

Specifications:
Part no.Intensification RatioAOil outputAir volume per strokeWeight
113211010.06388888934025 cc1.8 lit6 kg
11324000.06388888949340 cc2.8 lit6.5 kg
Yes! I am Interested

Hydraulic Block Cylinder

REQUEST CALLBACK

Hydraulic Block Cylinder
Approx. Rs 3,800 / Piece
Get Best Quote

Being a quality-driven association, we offer a qualitative cluster of Block Cylinder for Automobile Industry. These chambers are chromium plated and are appreciated for their vigorous development. Made of value tried steel, Block Cylinders are planned as per modified prerequisites of the customers.

Features:

  • Compact Design
  • Reliable
  • User Friendly
Yes! I am Interested

Pneumatic Swing Cylinder

REQUEST CALLBACK

Pneumatic Swing Cylinder
Approx. Rs 8,000 / Piece
Get Best Quote

Versions:

  • Following versions are available according to swing direction
  • While clamping & looking from rod side
  • CW-Clockwise
  • CCW- Counter clockwise

Specifications:


  • Bore diameter- 50 mm
  • Maximum air pressure- 6 bar
  • Minimum air pressure-2.5 bar
  • Clamping force-1 kN at 6 bar air pressure

Important Notes:


  • To avoid the damage of swing mechanism
  • Hold the clamping strap in a vice, while tightening and loosening the clamping strap nut
  • Clamp the job in the straight clamping stroke only
  • Do not exceed the standard strap length
  • For height adjustment, either use a spacer at the mounting plate or an adjusting bolt on the strap as shown in figure
  • To prevent the damage to swing mechanism due to impact use flow control valve at both ports.
  • Use only dry & lubricated air.
  • For ordering the seal kit, add the prefix "S" to the part number.
Yes! I am Interested

Hydraulic Power Unit

REQUEST CALLBACK

Hydraulic Power Unit
Approx. Rs 5,500 / Piece
Get Best Quote

With our rich industry experience in this domain, we are providing our valuable clients Hydraulic Power Unit. Our offered power unit is precisely manufactured at our well developed manufacturing unit employing high end technology. Additionally, we deliver this power unit from our end after conducting a proper test against them. Our honored clients can avail the offered power unit in various specifications.

Features:


  • Enhanced durability
  • Premium quality
  • Robustness

Specifications:


  • Motor: 3 phase, 1 hp, 1440 RPM
  • Pump- Gear pump: 1.8Ipm at 1500 rpm
  • Direction Control Valve Cetop-3 mounting, 3 position, solenoid operated
  • Pressure switches: 2 Nos
  • Pilot operated check valve
  • Tank capacity: 30 liters approximately
  • Useful oil volume: 25 liters approximately
  • Working pressure: 150 bar
  • Maximum oil pressure - 175 bar
  • Pendent cable length Maximum: 5 meters
  • Control panel
  • Length: 730 mm
  • Width: 580 mm
  • Total Height: 850 mm
Yes! I am Interested

Pneumatic Swing Cylinder

REQUEST CALLBACK

Pneumatic Swing Cylinder
Approx. Rs 8,200 / Piece
Get Best Quote

Description :

  • Pneumatic swing cylinders are used for clamping in the sheet metal industry and for light machining applications. In the unclamped position, the work piece area is free from the strap, for easy loading / unloading.
  • These are pull type cylinders. The piston rotates by 90° during the swing stroke, followed by straight clamping stroke.

Versions :

  • Swing direction (While clamping and looking from rod side)
  • CW – clockwise
  • CCW – counter clockwise

Specifications :

  • Bore diameter – 50 mm.
  • Maximum air pressure – 6 bar.
  • Minimum air pressure – 2.5 bar.
  • Clamping force – 1 kN at 6 bar air pressure.

Notes :

  • To avoid the damage of the swing mechanism, hold the clamping strap in a vice while tightening and loosening the clamping strap nut.
  • To prevent the damage to the swing mechanism due to impact, use a flow control valve at both the ports.
  • Clamp the job in the straight clamping stroke only.
  • Do not exceed the standard strap length.
  • For height adjustment, use either a spacer at the mounting plate or an adjusting bolt on the strap as shown in figure.
  • Use only dry and lubricated air.
  • For ordering the seal kit, add the prefix "S" to the part number.
Yes! I am Interested

View PDF

Swing Cylinder

REQUEST CALLBACK

Swing Cylinder
Approx. Rs 8,000 / Piece
Get Best Quote

Description:

  • Swing cylinders are pull type cylinders. The piston rotates by 90º during the swing stroke, followed by straight clamping stroke due to the internal cam.

Application:

  • The clamping strap rotates by 90º while clamping and declamping. Due to the swing action, loading and unloading of the job is very easy. In the unclamped position, the workpiece area is free from the strap.

Specifications:

  • Maximum oil pressure – 200 bar.
  • Minimum oil pressure – 30 bar.

Technical Details:

FORCE§

3.5KN

8.9 KN

13.9 KN

22.6KN

Ø BORE

25

40

50

63

d

20

32

40

50

A

65

75

85

105

B

54

60

65

80

C

48

75

100

120

DB

51

60

74

88

DT

NA

60

75

90

F

30

40

56

68

G

M18x1.5

M28x1.5

M36x1.5

M46x2

M

6.5

11

11

17

L

127.3

153

184

184

N

84.5

97

116

116

P

107.5

125

144

144

 

NA

52

67

67

T

15.5

16.5

15.5

18

Stroke total

18

24

24

24

SWING

9

10

10

10

CLAMP

9

14

14

14

Oil vol clamp

3 cc

11 cc

18 cc

28 cc

Oil volume

Declamp

9 cc

30 cc

48 cc

75 cc

Weight

2.2 kg

3.2 kg

4 kg

6 kg

TM CW

3510100

3520100

3530100

TM CCW

3510200

3520200

3530200

BM CW

BM CCW

3505100

3505200

3510300

3510400

3520300

3520400

3530300

3530400

STRAP NO.

3610900

3605200

3601400

3603100



 

Yes! I am Interested

Hydropneumatic Intensifier

REQUEST CALLBACK

Hydropneumatic Intensifier
Approx. Rs 20,000 / Unit(s)
Get Best Quote

Being a quality oriented organization, we present highly Hydropneumatic Intensifier. These help in displacing and increasing the pressure of oil by using air. Outstanding feature of our product includes cost of unit is low and custom based compact design offered with output pressure. These products are available at pocket friendly price range.

 

Features:

 

  • Compact design

  • Custom base

  • Low operating cost

  • Maximum output pressure


Description:


  • Hydropneumatic intensifiers are widely used on conventional machines, where hydraulic power unit is not available with the machine. Single acting elements are generally used with hydropneumatic intensifiers.

Principle


  • In the static condition, (Pressure x Area) at air side is equal to (Pressure x Area) at oil side. Hydropneumatic intensifier has one oil cylinder and one air cylinder. The pistons of both these cylinders are connected to each other. In single acting intensifier, the air cylinder is single acting, spring return. The air piston is the driving piston and the oil piston is the driven piston.

Operation


  • When air is allowed in the intensifier by a D.C. valve, oil on the hydraulic side gets pressurized and is forced out. The oil output operates the clamping cylinders and the job gets clamped. After releasing the air pressure, due to the spring in the intensifier, the air piston returns back and the job gets declamped. Oil is pushed back into the intensifier due the spring in the cylinder.

Leakage Compensation (Make up oil system)


  • This is an important feature of hydropneumatic intensifier. The oil- side of the hydropneumatic intensifier, hydraulic hoses and cylinders form a close loop system. Oil in this loop is a confined fluid. There must be a leakage compensation for the confined oil, if there is any leakage (across piston of cylinder and through connectors). The make-up oil system compensates for leakage by adding small volume of oil at every stroke. In the unpressurised mode, make-up oil is always connected to the oil side. In the pressurization stroke, as the piston moves up and crosses the high pressure seal, the make-up oil gets disconnected from the oil side. In case of leakage, when the system pressure is released after operation, the hydraulic piston moves down to the bottom. When it crosses the high pressure seal, the make-up oil gets connected to the oil side. Any leaked-out volume causes vacuum on the oil side and is automatically compensated due to the atmospheric pressure.

Installation :


  • Please see "More About Hydropneumatic System" and "Bleeding and Trouble Shooting of Closed loop system".

Notes


  • For ordering the seal kit, add the prefix "S" to the part number.

Selection of intensifier


  • Intensification Ratio: For 5 to 7 bar air pressure, select an intensification ratio of 28 so as to get about 150 bar hydraulic output. For 3.5 to 4 bar air pressure, select an intensification ratio of 40 to get about 150 bar hydraulic output.
  • Oil Output: Oil volume for every cylinder is given in the catalogue. Sum up all the oil volumes of the cylinders to get the total oil requirement. Intensifier output must be more than the total oil volume required.

 

To use 2 cylinders of part no. 1510200 and 2 cylinders of part no. 1540100 for clamping a job,
Oil required = (oil volume of 1510200) x 2 + (oil volume of 1540100) x 2 = (22 x 2) + (34 x 2) = 112 cc
Select the part no. 1128200 with 200 cc oil output.

 

Yes! I am Interested

Compact Cylinder

REQUEST CALLBACK

Compact Cylinder
Approx. Rs 2,750 / Piece
Get Best Quote

We are recognized providers of Compact Cylinder that are in conformation with the set industry standards and have a long functional life. These cylinders are robustly constructed in our sophisticated facility, following rigorous quality parameters as per worldwide standards. Moreover, Compact Cylinder is simple to install and absolutely cost effective.

 

Features:


  • Precise dimensions

  • Magnetic position detection

  • Sturdily constructed

  • Long functional life


Description

  • Compact cylinders are solid piston, double acting. Cylinders are very compact in the axial direction.

Advantages

  • These cylinders are used where height is a constraint. Mounting of the cylinder is very easy.

Specifications

  • Maximum operating pressure – 150 bar.
  • Double rod end cylinders can be available on request.

Note

  • Due to compact design, port thread depth is short.
  • Reduce the standard connector thread length to suit the port depth.
Yes! I am Interested

Die Clamping Cylinder

REQUEST CALLBACK

Die Clamping Cylinder
Approx. Rs 18,000 / Piece
Get Best Quote

Our organization is renowned as one of the leading providers of Die Clamping Cylinder. All components of these cylinders are of elevated standard quality resulting in durability. Under skilled guidance of our engineers and technicians, we provide an extensive variety of Die Clamping Cylinder. These are designed using latest technology and high quality raw material that are sourced from reliable and trusted vendors. We offer these at industry leading price to our esteemed clients.

 

Features:


  • Easy operations

  • Maintenance free

  • Sturdiness

  • Reliability


Die clamping cylinder is a pull type, spring return cylinder. An integral 'T', suitable to 28 mm 'T' slot, is provided to the piston rod of the cylinder.

Application

  • These cylinders are widely used for the quick change of dies & tools on presses.

Operation

  • For changing the tool, first the cylinder pressure is released and the cylinders are moved away from the tool, either manually or by a pneumatic cylinder. After changing the tool, cylinders are placed back at the clamping points and are pressurised.

Important Notes

  • Two separate circuits should be used for two diagonals of the tool (Tandem Clamping). This feature is a must for the safety purpose.
  • Cylinder stroke is only 8 mm. Clamping height of different tools must be the same with the tolerance of ±1 mm. Specify dimension 'H' (clamping height of the tool), while ordering the cylinder.
  • For ordering the seal kit, add the prefix "S" to the part number.
  • T Slot dimensions are as per DIN 650. For different T Slot dimensions give all details.

Specifications

  • Maximum operating pressure – 200 bar.
Yes! I am Interested

Die Lifter

REQUEST CALLBACK

Die Lifter
Approx. Rs 48,000 / Piece
Get Best Quote

Description:

  • Die Lifers are used in pairs or sets as per the 'T' slot length in the bolster. Hydraulic piston fitted with needle roller bearing lift the dieset allowing the die to be easily rolled in and out during die change process. Die lifter is of rectangular cross section & can be fitted in 'T' Slot of bolster. In 250 mm & 200 mm length die lifters, four & three single acting, load return cylinders are fitted respectively. Various lengths can be assembled by using combinations of 250 & 200 length die lifters.

Application:

  • Die-lifters are used for quick change of dies & tools on presses. Die can be pushed & pulled only in the direction of T slot.

Specifications

  • Operating pressure – 85 kg/cm
  • Max. operating pressure 100 kg/cm
  • Force per unit length :- 5 kg/mm at 85 bar
  • Stroke :- 3 mm
  • Lengths Available- 200, 250, 400, 450, 500, 600, and any length in step of 50 above 600 mm

Installation

  • Die-lifters are fixed in T slot. Die-lifters must be 1 mm below bolster top in un pressurized mode. Proper packing should be used to achieve this specific height. Connector tubes are used to connect two units of die-lifter in the row as shown in figure. Minimum two rows of die-lifter are required to balance die weight. At one end hydraulic connection has to be give & other end has to be plugged.

Operation

  • For changing die, first unclamp the die-set. (Keep all cylinders in Parking stand, if die is clamped by die clamping cylinders) Move ram up. Pressurize die-lifter, so that die is lifted by 2 mm above bolster top. Push die-set on trolley. Push new die set on bolster. Release die-lifter pressure so that die will rest on bolster.

Note

  • There should not be pockets on the bottom of die-sets. It is preferred to have hardened strip at bottom area which is in contract with die-lifters.
  • Do not pressurize die-lifters when either dies are in clamped condition on Ram is at bottom dead center.
  • Die-lifter circuit must have counter balance valve relief valve so that maximum pressure is controlled.
  • For ordering the seal kit, add prefix “S” to the part number (Specify total length and number of rollers).
  • T slot dimensions should be 28 mm as per DIN 650 standard
  • Specify dimension 'L' (Length of die lifter), while ordering the die lifter.
Yes! I am Interested

Hollow Piston Cylinder

REQUEST CALLBACK

Hollow Piston Cylinder
Approx. Rs 3,900 / Piece
Get Best Quote

Description

  • Hollow piston cylinders are single acting, spring return cylinders, suitable to use with hydropneumatic intensifiers. The piston is provided with a through hole.

Advantages

  • Hollow piston cylinders can be easily adapted on existing fixtures. The cylinder can be mounted on the stud, by increasing the stud length. Automation can be achieved very fast.

Installation

  • With the help of a back mounting plate, the hollow piston cylinder can be mounted on the stud.
  • The cylinder can also be used to pull the stud, by mounting it on the other side of the base plate as For this arrangement, a wiper should be provided to the stud for 10 mm stroke cylinders.

Specifications

  • Maximum oil pressure – 200 bar.
  • Return spring back pressure-@1 bar.

Notes

  • As the cylinder is single acting, spring return, a breather is provided. It should be protected from cutting liquids and coolants.
Yes! I am Interested

Hydraulic Power Unit

REQUEST CALLBACK

Hydraulic Power Unit
Approx. Rs 50,000 / Piece
Get Best Quote

Description:

  • This hydraulic power unit is specially designed for clamping application only. Special care is taken to avoid oil heating problem. This hydraulic power unit is suitable to operate double acting clamping cylinders in parallel.

Operation:

  • In clamping & declamping mode, after reaching the set pressure, which is sensed by a pressure switch, direction control valve shifts to the centre-position, unloading pump delivery to the tank . In case of pressure drop, the direction control valve operates to increase pressure, to the set pressure. The system includes all relevant electrical and mechanical accessories. Pendent with clamp unclamp push buttons is provided along with the system.

Specifications:

  • Motor – 3 phase, 1 hp, 1440 RPM.
  • Pump – Gear pump 1.8 lpm at 1500 rpm.
  • Direction Control Valve – Cetop-3 mounting, 3 position, solenoid operated.
  • Pressure switches- 2 Nos.
  • Pilot operated check valve.
  • Tank capacity – 30 liters approximately
  • Useful oil volume – 25 liters approximately
  • Working pressure – 150 bar
  • Maximum oil pressure – 175 bar
  • Pendent cable length Maximum – 5 meters.
  • Control panel.
  • Length – 730 mm
  • Width – 580 mm
  • Total Height – 850 mm

Note:

  • Clamping time in seconds = total oil volume at clamping side of all the cylinders in cc divided by pump output (28 cc per second)
  • Declamping time in seconds = total oil volume at declamping side of all the cylinders in cc divided by pump output (28 cc per second)
  • While using single acting cylinder on Hydraulic power unit make sure that return line have minimum resistance to the flow
  • Special care has taken to avoid electric shocks while designing control panel
Yes! I am Interested

Hydraulic Cylinders

REQUEST CALLBACK

Hydraulic Cylinders
Approx. Rs 3,500 / Piece
Get Best Quote

Specifications:

  • Max. pressure – 160 bar.
  • Max reciprocating speed – 12 m/min.
  • Break-away pressure-3 to 5 bar.
  • Standard cushioning length – 20 mm.
  • Minimum cushioning speed – 400 mm/min or less adjustable.
  • Cushioning is available from 63 mm bore onwards only.
  • For Bronze filled teflon seals, min. speed without stick-slip – 5 mm/min.

Features and Benefits:

  • The Piston Rod is toughened, ground, hard chrome plated and polished to ensure a smooth, dent & rust resistant surface for best sealing and long life. The Cylinder Tube is to meet close standards of straightness, roundness and surface finish for longer seal life and performance.

Other details:

 

BORE

 

ROD

 

A

 

B

 

D

 

E

 

E E

 

G F

 

J

 

K K

 

N A

 

P J

 

T G

 

W H

 

Y

 

Z B

25

12

14

24

10

40

1/4"

35

20

M 10 x 1.25

11

53

28.3

15

50

121

40

18

28

18

28

30

42

15

22

63

3/8"

39

30

M 14 x 1.5

M20x1.5

17

26

73

41.7

25

62

166

50

22

36

22

36

34

50

18

30

75

1/2"

40

32

M 16 x 1.5

M 27 x 2

21

34

74

52.3

25

67

176

63

28

45

28

45

42

60

22

36

90

1/2"

37

32

M 20 x 1.5

M33x2

26

43

80

64.3

32

71

185

80

36

56

36

56

50

72

30

46

115

3/4"

44

38

M 27 x 2

M 42 x 2

34

54

93

82.7

31

77

212

100

45

70

45

63

60

88

36

60

130

3/4"

43

38

M 33 x 2

M48x2

43

68

101

96.9

35

82

225

Yes! I am Interested

Manifold Mounting Cylinder

REQUEST CALLBACK

Manifold Mounting Cylinder
Approx. Rs 1,100 / Piece
Get Best Quote

Description:

  • These clamping cylinders are single acting spring return cylinders. These cylinders are fitted either in tapped hole in fixture, or in manifold. Sealing ‘O’ Ring is provided on the face of the cylinder.

Advantages:

  • These cylinders are suitable to clamp smaller workpieces & when two or more jobs are clamped with short distance in between. The advantage of these cylinders is piping gets eliminated.

Installation:

  • Sealing ring is provided on the face of cylinder, for proper sealing resting face should be flat & square to thread axis.

Notes:

  • Manifold mounting cylinders must not be subjected to a load in retracted position.
  • These cylinders must not be loaded in unpressurised mode. Minimum wall thickness 3 mm for manifold. Aggressive cutting fluids & coolant can damage elastomer of the seal. Sealing may not be effective in this case. Hence breather must be protected from these fluids.

 

Technical Details:

PART NO.

1703500

1703600

1730700

1730800

FORCE §

0.75 kN

3 kN

7.22 kN

12 kN

Ø Bore

8

16

25

32

a

M12x1.5

M24x1.5 M36x1.5

M42x1.5

 

b

13

14

21

25.8

c

40

45

52

59

d

5

10

16

20

e

46

51

58

65

f

NA

NA

M10

M12

SW1

16

27

41

50

SW2

NA

8

14

16

Max. seating

torque (Nm)

10

110

130

225

Min Spring

Force

12.7 N

57.7 N

106.3 N

164.9 N

Weight

55 gm

190 gm

580 gm

1030 gm

OIL VOLUME

0.5 cc

2 cc

5 cc

8 cc

Yes! I am Interested

Pneumatic Swing Cylinder

REQUEST CALLBACK

Pneumatic Swing Cylinder
Approx. Rs 8,000 / Piece
Get Best Quote

Description:


  • Pneumatic swing cylinders are used for clamping in the sheet metal industry and for light machining applications. In the unclamped position, the work piece area is free from the strap, for easy loading / unloading.These are pull type cylinders. The piston rotates by 90° during the swing stroke, followed by straight clamping stroke.

 

Versions:


  • Swing direction (While clamping and looking from rod side)
  • CW – clockwise
  • CCW – counter clockwise


Specifications:


  • Bore diameter – 50 mm.
  • Maximum air pressure – 6 bar.
  • Minimum air pressure – 2.5 bar.
  • Clamping force – 1 kN at 6 bar air pressure.


Notes:


  • To avoid the damage of the swing mechanism, hold the clamping strap in a vice while tightening and loosening the clamping strap nut.
  • To prevent the damage to the swing mechanism due to impact, use a flow control valve at both the ports.
  • Clamp the job in the straight clamping stroke only.
  • Do not exceed the standard strap length.
  • For height adjustment, use either a spacer at the mounting plate or an adjusting bolt on the strap as shown in figure.
  • Use only dry and lubricated air.
  • For ordering the seal kit, add the prefix "S" to the part number.

 

Yes! I am Interested

Pull Cylinder

REQUEST CALLBACK

Pull Cylinder
Approx. Rs 4,800 / Piece
Get Best Quote

Description:


  • Pull cylinders are single acting, spring return cylinders, suitable for use with a hydropneumatic Intensifier.


Installation:


  • A square flange with 4 mounting holes is provided on the front side for mounting purpose. The cylinder can be mounted on the front flange. The cylinder can be mounted on the back side with long screws.


Specifications:


  • Maximum operating pressure – 200 bar.
  • Return spring back pressure – 1 bar.


Technical Details:

PART NO.

1910100

1920100

1930100

FORCE §

11 kN

22 kN

30 kN

ØBORE

38

50

60

STROKE ±1

15

15

15

A

45

55

68

B

60

67

85

C

7

9

11.0

D

52

62

78

D1

38

45

65

d

22

25

32

E

M 12

M 16

M 20

G

1/4"

1/4"

3/8"

L

50

50

58

SW

17

20

28

MIN SPRING FORCE

415 N

501 N

507 N

OIL VOL

12 cc

22 cc

30 cc

WEIGHT

1.5 kg

2.5 kg

3.5 kg

 

Yes! I am Interested

Threader Body Cylinder

REQUEST CALLBACK

Threader Body Cylinder
Approx. Rs 2,200 / Piece
Get Best Quote

Technical Details:

FORCE §

3 kN

5 kN

10 kN

18 kN

30 kN

30 kN

50 kN

ØBORE

16

20

30

40

50

50

65

D

21.8

27.5

43.5

54.5

67.5

67.5

83

d

9.52

11.09

15.87

20.6

25.4

25.4

34.9

D1

30

36

54

65

78

78

96

E

9

10

12

12

14

14

14

F

M 2 4x 2

M 30 x 2

M 4 6x 2

M 57 x 2

M 70x 2

M 70 x 2

M 86x 2

G

1/8"

1/8"

1/4"

1/4"

3/8"

3/8"

3/8"

H

12

12

12

12

12

12

15

J

7

8

9

13

15

15

20

K

M 6

M 6

M 10

M 12

M 16

M 16

M 16

M

-

M 6

M 6

M 8

M 10

M 10

M 12

P

-

20

30

36

48

48

56

SW

8

10

13

18

21

21

30

PART NO.

1710100

1720100

1730100

1740100

1750100

1750300

1760100

STROKE ±1

15

10

10

10

10

50

25

L

78

70

72

77

81

160

110

L1

58

49

47

52

54

90

83

Min Spring

Force

 

79.8 N

 

131 N

 

197 N

 

265 N

 

461 N

 

321.8 N

 

516.3 N

OIL VOL

3 cc

3 cc

7 cc

13 cc

20 cc

100 cc

84 cc

WEIGHT

0.25 kg

0.5 kg

1 kg

1.5 kg

2 kg

3.5 kg

4.8 kg

 








 

Yes! I am Interested

Vertical Swing Cylinder

REQUEST CALLBACK

Vertical Swing Cylinder
Approx. Rs 8,000 / Piece
Get Best Quote

Vertical Swing Cylinder are used in applications similar to that of swing cylinders and can replace swing cylinders in many places. In the unclamped position, the work piece area is free from the strap, to facilitate easy loading / unloading.

Technical Details:

PART NO.

 

U

 

V

 

AB

 

DB

 

R

 

W

 

SP

 

ST

 

Z

 

CT

 

CA

 

WA

 

TP

 

X

 

Y

 

CH

 

WEIGHT

3204400

24.3

16.5

6.5

10

16

8

12

6

18.5

23.5

6

11.8

M6

6

6

4

0.15 kg

3201700

32

13

13

18

26

18

11

10.1

24

28

14

22

M6

8

12

5

0.2 kg

200500

40

15

16

22

32

24

12.5

12.1

30

38

12

26

M10

10

15

6

0.4 kg

3203400

64

20

24

32

48

38

20.5

20.1

48

65

13

38

M16

16

22

10

1 kg

Yes! I am Interested

Work Support

REQUEST CALLBACK

Work Support
Approx. Rs 2,200 / Piece
Get Best Quote

Hydraulic work support is a replacement to the adjustable screw jack. This is not a force giving element but a resistance giving element. This work support replaces both spring forwarding as well as pneumatic forwarding work support.

Application:

  • Irregular job is supported on only three points. If an additional support is required, it must be adjustable, like the manual screw jack support. Hydraulic work support is the right solution for such an application. The work support is used to support the job, to avoid deflection and vibrations marks due to cutting and clamping forces. It helps to clamp the job without any distortion.

Specifications:

  • Minimum hydraulic operating pressure – 100 bar.
  • Maximum hydraulic operating pressure – 200 bar.
  • For work support 3311500, elastic deformation under load is approx. 0.002 mm per kN.
  • For work support 3320500, elastic deformation under load is approx. 0.001 mm per kN.

Technical details:

PART NO.

3311500

3320500

SUPPORT FORCE §

5 kN

10 kN

a

70

85

b

57

70

c

95

106

d

66

78

e

119.4

132

f

21

36

g

21

36

h

9

11

Stroke ± 1

15

15

Weight

3 kg

4 kg

 

 

 

Plunger Contact Force Max.

80 N

100 N

Yes! I am Interested

Hydraulic Coupling Unit

REQUEST CALLBACK

Hydraulic Coupling Unit
Approx. Rs 850 / Piece
Get Best Quote

Backed by a team of skilled professionals we are able to offer our clients a wide range of Hydraulic Coupling Unit. Comes with hydraulic power unit with control panel, the offered coupling unit is manufactured at our production unit using the better quality components and advance technology in accordance with defined industry standards. This coupling unit has become the preferred choice of the patrons due to its striking features. We assure our customers that this coupling unit is excellent on counts of durability and quality.

Features:


  • Precisely designs
  • Robust construction
  • Extended Durability

Coupling Unit Specifications:


  • Minimum operating pressure: 50 bar
  • Maximum operating pressure: 250 bar
  • Accumulator charging pressure: 0.9x minimum operating pressure
  • Accumulator volume: 75 cc
  • Total volume of the cylinder: 500 cc

Power unit specifications:


  • Hydraulic power unit with control panel: 4500051
  • Pump output: 1.81 pm
  • Motor: 3 phase, 1 hp
  • Tank capacity: 30 litres approximately
  • Useful oil volume: 25 Litres approximately
Yes! I am Interested

View PDF

Die Clamping Cylinder

REQUEST CALLBACK

Die Clamping Cylinder
Approx. Rs 8,200 / Piece
Get Best Quote

With our rich industrial experience in this domain, we are engaged in offering our clients a vast assortment of Die Clamping Cylinder which used for the quick change of dies and tools on presses, our offered clamping cylinders are strongly built with high quality material and hi tech technology. We make certain that our offered clamping cylinders are outstanding on counts of durability and quality. We provide these clamping cylinders in various specifications as per the needs of customers.

Features:


  • Compact design
  • High performance
  • Durability

Applications:


  • These cylinders are widely used for the quick change ef dies and tools on presses

Operations:


  • For changing the tool, first the cylinder pressure is released and the cylinders are moved from the tool, either manually or by a pneumatic cylinder
  • After changing the tool, cylinders are placed back at the clamping points and are pressurised

Specifications:


  • Maximum operating pressure: 200 bar
Yes! I am Interested

View PDF

Swing Cylinder

REQUEST CALLBACK

Swing Cylinder
Approx. Rs 8,000 / Piece
Get Best Quote

Specifications:

  • Bore diameter-30 mm
  • Maximum oil pressure- 200 bar
  • Minimum oil pressure-20 bar
  • Oil volume clamp- 9.2 cc
  • Oil volume declamp-19.8 cc
  • Force at 150 bar- 5.0 kN
  • Weight of the cylinder- 2.8 kg
Yes! I am Interested

Block Hydraulic Clamping Cylinders

REQUEST CALLBACK

Block Hydraulic Clamping Cylinders
Approx. Rs 8,000 / Piece
Get Best Quote

Block Cylinder offered provide working as integrated structure comprising cylinder of reciprocating engine.

 

Features:

 

  • High performance oriented block cylinders
  • Superior metal casting finish containing cylinders and cooling channels/fins of reciprocating internal-combustion engine

 

Specifications:

 

  • Precision construction with each cylinder fitting precisely into its respective hole
  • Cylinders can be made available in different dimensions
  • Made available in different height options
  • Can also be made available in OEM specifications
  • Made available at competitive prices
Yes! I am Interested

View PDF

Single Hydraulic Cylinder

REQUEST CALLBACK

Single Hydraulic Cylinder
Approx. Rs 3,900 / Piece
Get Best Quote

Specifications:

  • Minimum hydraulic operating pressure- 100 bar
  • Maximum hydraulic operating pressure-200 bar
  • For work support 3311500, elastic deformation under load is approx. 0.002 mm per kN
  • For work support 3320500, elastic deformation under load is approx. 0.001 mm per kN
Yes! I am Interested

Standard Hydraulic Cylinder

REQUEST CALLBACK

Standard Hydraulic Cylinder
Approx. Rs 2,800 / Piece
Get Best Quote

Specifications:

  • Minimum hydraulic operating pressure- 100 bar
  • Maximum hydraulic operating pressure- 200 bar
  • Maximum plunger contact force- 4 N
  • Support force 1.5 kN at 150 bar

Advantages:


  • Compact in size
  • Plunger is normally in retracted condition
Yes! I am Interested

Threaded Body Cylinder

Threaded Body Cylinder
Approx. Rs 2,500 / Piece
Yes! I am Interested

View PDF


Manifold Mounting Cylinder

Manifold Mounting Cylinder
Approx. Rs 3,000 / Piece
Yes! I am Interested

View PDF


Hollow Piston Cylinder

Hollow Piston Cylinder
Approx. Rs 2,200 / Piece
Yes! I am Interested

View PDF


Compact Cylinder

Compact Cylinder
Approx. Rs 3,200 / Piece
Yes! I am Interested

View PDF


Pull Cylinder

Pull Cylinder
Approx. Rs 2,200 / Piece
Yes! I am Interested

View PDF


Vertical Swing Cylinder

Vertical Swing Cylinder
Approx. Rs 8,000 / Piece
Yes! I am Interested

View PDF


 
X


Call Us: +91-8079466321
Neotech Equipments Pvt. Ltd.
Rahul Gore (Director)
No. 401, Gagan Deep Building- 12, Rajendra Place ,
New Delhi - 110008, Delhi, India
Contact via E-mail
Contact via SMS



Home  |   Profile   |  Our Products  |  Site Map  |   Contact Us   |   Mobile Site

© Neotech Equipments Pvt. Ltd.. All Rights Reserved (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited

Neotech Equipments Pvt. Ltd.