Lubrication and Mechanical Tools

An attempt should always be made to dismount any machine element including bearings, pulleys,couplings and gears without damaging them, especially where the intention is to remount them.Most of the Mechanical Puller available today have serious limitations since the jaws slip, tip of jaws bend/break, threads of spindle gets damaged. Pull Right Extractor overcome all these limitations of conventional pullers.
The major advantages of these pullers are:

• The two/three jaws slide backward/forward on precision ground Tee section. The jaws are coplanar over the entire width thus ensuring FULL GRIP over the machine element requiring extraction.
• There is a facility of locking puller jaws to avoid any SLIPPAGE while extracting machine elements like bearings, pulleys, couplings etc.
• All parts are made from high-grade alloy steel, toughened to 25-30 Rc and precision ground to maintain parallelism of jaws. Spindle is of EN 24 and Nitrided. This ensures high LOAD CARRYING CAPACITY and also gives long life to the puller.
• There is a rotating center to reduce damage to shaft. A specially designed Tommy is provided to apply extra torque required to remove jammed pulleys/couplings. A gunmetal ring has also been provided to eliminate damage to spindle.

We are leading supplier of Constant Level Oiler. In many oil lubricated machines it is essential to maintain a constant level of oil to properly lubricate machine elements in motion. Excessive oil level increases resistance resulting in higher oil temperature.This causes faster ageing and breakage of oil seals, which means frequent oil leakages. Low oil level is a sure recipe for equipment failure.Generally a constant level of oil is required wherever ‘SPLASH’ lubrication technique is employed. In this system of lubrication rotating element causes a ‘splash’ due to its rotation and this splashed lubricant in turn lubricates all other machine elements within the system. Splashing would occur if part of rotating element is in oil and part is above the oil. Rf. Fig.1 The right answer is to install an efficient, reliable constant level oiler. ‘LUBEX’ constant level oil consists of a polycarbonate (PC) dome with suitable aluminium alloy base and elbow to fit your equipment. PC has the advantage of extraordinary impact strength (virtually unbreakable), excellent clarity, and good temperature range (110 ° c). A lock nut facilitates keeping the oiler upright without overtightening elbow.
The PC dome is threaded and can be cleaned periodically if required. The entire design is totally modular, thus any individual component of the oiler can be replaced at any point of time.The working principle of ‘LUBEX’ constant level oiler is extremely simple. As and when oil level falls below level ‘x’ air passage is opened, you will notice bubbling taking place within PC dome.Oil flows from PC dome into the machine causing oil level to rise with in the machine. The moment oil level in the equipment reaches level ‘x’ air passage is blocked bubbling stops and oil from PC dome stops going into the machine. Ref. fig.2 Thus oil in PC dome goes on decreasing, but oil within the machine is maintained at a constant level.Oil can be recharged in PC dome at any point of time by simply unscrewing base and refilling PC dome with an oil can. The product is designed and manufactured to last for several years, an excellent investment for oil lubricated machines requiring a constant level of oil.

Shaft Alignment kit is used for the contribution in enhancing life of the coupling, bearing ,seal etc. It consists of a aluminium vee block that can be clamped on the hub of coupling by wing nuts. The kit has two precision spirit level in the vee block to get accurate indexing of 90, 180, 270 and 360 degrees.

Technical Specifications:

Drip Oilers provide a convenient and economical method of lubricating bush bearings; machine slides etc.The oiler dispenses oil by gravity from a reservoir through a needle valve with manual shut off.Operator can set drip rate by simply adjusting sensitive needle valve and viewing drip rate in sight glass. Once drip rate has been set, it should be locked.A suitable locking nut is provided for this purpose.On/off is by means of a toggle pin. .Oil reservoir is made of polycarbonate which facilitates easy visual check of oil level. polycarbonate also has the advantage of high impact strength, excellent clarity and good temperature stability. These dripoiler could conveniently replace existing glass type drip oilers which are prone to breakage. .The oiler has a fixed thread size of 1/8" bsp. for anyother thread size a suitable adaptor is provided.